snmp3_set Set the value of an SNMP object php函数


snmp3_set

(PHP 4, PHP 5)

snmp3_setSet the value of an SNMP object

说明

bool snmp3_set ( string $host , string $sec_name , string $sec_level , string $auth_protocol , string $auth_passphrase , string $priv_protocol , string $priv_passphrase , string $object_id , string $type , string $value [, int $timeout = 1000000 [, int $retries = 5 ]] )

snmp3_set() is used to set the value of an SNMP object specified by the object_id.

Even if the security level does not use an auth or priv protocol/password valid values have to be specified.

参数

host

The hostname of the SNMP agent (server).

sec_name

the security name, usually some kind of username

sec_level

the security level (noAuthNoPriv|authNoPriv|authPriv)

auth_protocol

the authentication protocol (MD5 or SHA)

auth_passphrase

the authentication pass phrase

priv_protocol

the privacy protocol (DES or AES)

priv_passphrase

the privacy pass phrase

object_id

The SNMP object id.

type

The MIB defines the type of each object id. It has to be specified as a single character from the below list.

types
=The type is taken from the MIB
iINTEGER
uINTEGER
sSTRING
xHEX STRING
dDECIMAL STRING
nNULLOBJ
oOBJID
tTIMETICKS
aIPADDRESS
bBITS

If OPAQUE_SPECIAL_TYPES was defined while compiling the SNMP library, the following are also valid:

types
Uunsigned int64
Isigned int64
Ffloat
Ddouble

Most of these will use the obvious corresponding ASN.1 type. 's', 'x', 'd' and 'b' are all different ways of specifying an OCTET STRING value, and the 'u' unsigned type is also used for handling Gauge32 values.

If the MIB-Files are loaded by into the MIB Tree with "snmp_read_mib" or by specifying it in the libsnmp config, '=' may be used as the type parameter for all object ids as the type can then be automatically read from the MIB.

Note that there are two ways to set a variable of the type BITS like e.g. "SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}":

  • Using type "b" and a list of bit numbers. This method is not recommended since GET query for the same OID would return e.g. 0xF8.
  • Using type "x" and a hex number but without(!) the usual "0x" prefix.

See examples section for more details.

value

The new value

timeout

The number of microseconds until the first timeout.

retries

The number of times to retry if timeouts occur.

返回值

成功时返回 TRUE, 或者在失败时返回 FALSE.

If the SNMP host rejects the data type, an E_WARNING message like "Warning: Error in packet. Reason: (badValue) The value given has the wrong type or length." is shown. If an unknown or invalid OID is specified the warning probably reads "Could not add variable".

范例

Example #1 Using snmp3_set()

<?php
  snmp3_set
('localhost''james''authPriv''SHA''secret007''AES''secret007''IF-MIB::ifAlias.3''s'"foo");
?>

Example #2 Using snmp3_set() for setting BITS SNMP object id

<?php
  snmp3_set
('localhost''james''authPriv''SHA''secret007''AES''secret007''FOO-MIB::bar.42''b''0 1 2 3 4');
// or
  
snmp3_set('localhost''james''authPriv''SHA''secret007''AES''secret007''FOO-MIB::bar.42''x''F0');
?>

« 
» 
快速导航

Copyright © 2016 phpStudy | 豫ICP备2021030365号-3